Repair clamp Type DI
Product characteristics
Repair clamps are flexible clamps composed of one, two or three stainless steel parts with ductile iron clamps attached to their ends with bolts and nuts for tightening. They are intended for easy, fast and permanent repair of corroded or damaged water pipes. The central bolt is with extended length for easier installation in difficult conditions. Working pressure PN10/16.Material
- Body and side plates made of stainless steel 1.4301 (AISI 304)
- Clamps of ductile iron in accordance with EN 1563:2018
- Surface protection of clamps with epoxy paint or black thermoplastic confirmed by an accredited laboratory issued health safety report
- EPDM rubber seal in accordance with the EN 681 -1:1996/A1:1998 with an accredited laboratory issued health safety certificate
- Screws, nuts and washers – Stainless steel (Class A21A4)
Field of application
- Above the ground installation.
- Underground installation.
Repair clamp Type S
Product characteristics
Repair clamps are flexible clamps made of one or two stainless steel parts wrapped with rubber gasket. They are intended for easy, fast and permanent repair of corroded or damaged water pipes.
The single band repair clamps are with tolerance of 10mm,
whereas the double band repair clams have 20mm tolerance.
Material
• Body and bands – stainless steel
• Rubber gasket – EPDM or NBR
• Nuts, bolts and washers – stainless steel
Field of application
• Above ground installation.
• Underground installation
DOWNLOAD SPECIFICATIONS (PDF)
Resilient Seated Gate Valve – F5
Features:
• Replaceable O-rings
• Low torque operation
• Rubber encapsulated wedge (optional
wedge with integrated sliders).
• Clockwise closing direction
• Epoxy coating protection in
accordance with EN 14901:2014
confirmed by health inspection
certificate
• Product color: Blue RAL 5005
• Maximum temperature: 80°C
DOWNLOAD SPECIFICATIONS (PDF)
Resilient seated gate valve F4
Features
- Replaceable O-rings
- Rubber encapsulated wedge (optional wedge with integrated sliders)
- Clockwise closing direction
- Epoxy coating protection in accordance with EN 14901:2014 confirmed by health inspection certificate
- Product color: Blue RAL 5005
- Maximum temperature: 80°C
Rubber Expansion Joint
• Flexible main shell made of EPDM in accordance
with EN 681-1:1996/A3:2005 with inner
reinforcements to provide consistency
• Steel galvanized loose flanges in accordance with
EN 1092-1:2007+A1:2013/AC:2014
• Working Pressure: PN10, PN16.
• Working Pressure: PN10, PN16.
• Available range: DN 50-600.
• Easy to install due to their light weight and
relatively small space requirement.
• Noise and vibrations caused by equipment such as
pumps are absorbed by Rubber Joints.
• Rubber Joints balance thermal movements appear
in any rigid system due to temperature changes.
Single chamber air valve
Features
• Design: EN 1074-4:2000
• Available range of DN sizes DN 50 to DN 100.
• Epoxy coated from the inside and outside, min 250
μm in accordance with EN 14901:2014
• Product color: Blue RAL 5005.
• Working pressure PN10 and PN16
DOWNLOAD SPECIFICATIONS (PDF)
Sluice gates Penstocks
Features
• Purpose: Wastewater treatment and mini hydro power plants.
• Made in accordance with EN 1085:2007
• Three or four side sealing
• Manual board lifting (option with hydraulic drive)
• Material:
Frame: Stainless steel in accordance with EN1.4301/X5CrNi 18-10 AISI 304
• Table: Hot rolled structural steel in accordance with EN 10025-2:2004 (option
stainless steel in accordance with EN1.4301/X5CrNi 18-10 AISI 304)
Stem: Stainless steel in accordance with EN 1.4301/X5CrNi 18-10 AISI 304 or
hydraulic cylinder with clip material C45E (1.991) in accordance with EN10277-
5:2008
Sealing tape: Hot roller structural in accordance with EN 10025-2:2004 or
stainless steel in accordance with EN 1.4301/X5CrNi 18-10 AISI 304
• Seal: EPDM rubber in accordance with EN 681-1:1996/AC:2002
• Surface protection by materials made of hot rolled structural steel with epoxy or
polyurethane color
DOWNLOAD SPECIFICATIONS (PDF)
Steel Max coupling for large diameters
Features:
• Body and end ring made of hot rolled
products of structural steel St235JR in
accordance with EN 10025-2:2019 or ductile
iron in accordance with EN 1563:2018
• Couplings produced in accordance with EN
14525:2004
• Protection with epoxy coating in accordance
with EN 14901:2014 or black thermoplastic
coating confirmed by health inspection
certificate
• PN16 working pressure
• Equipped with steel zinc coated bolts, nuts
and washers
• EPDM rubber seal in accordance with EN
681- 1:1996
• High tolerance mechanical pipe fitings
DOWNLOAD SPECIFICATIONS (PDF)
Steel max flange adapter for large diameters
Features:
• Body and end ring made of hot rolled products of structural
steel ST235JR in accordance with EN 10025-2:2019 оr ductile
iron in accordance with EN 1563:2018
• Flange Adaptors produced in accordance with EN 14525:2004
• Epoxy coating protection in accordance with EN 14901:2014 or
black thermoplastic coating confirmed by health inspection
certificate
• PN10, PN16 working pressure
• Connecting dimensions in accordance with EN 1092-
1:2007+a1:2013/AC:2014 or EN 1092-2:1997
• Equipped with steel zinc coated bolts, nuts and washers
• EPDM rubber seal in accordance with EN 681-1:1996
• High tolerance mechanical pipe fitting
DOWNLOAD SPECIFICATIONS (PDF)
Strained Flange Adapter for HDPE and PVC pipe
Features:
• Body and end rings are made of
ductile iron material EN- GJS-500
(GGG 50) in accordance with EN
1563:2018 standard
• Flange Adaptоrs produced in
accordance with EN 14525:2004
• Epoxy coating protection in
accordance with EN14901:2014 or
black color thermoplastic coating
confirmed by health inspection
certificate
• PN10, PN16 working pressure.
• Flanges in accordance with
EN1092- 2:1997
• Equipped with steel zinc plated
bolts, nuts and washers
• EPDM rubber seals in accordance
with EN 681-1:1996
• Angular deflection +/- 3.5⁰
DOWNLOAD SPECIFICATIONS (PDF)
Swing check valve
Features
• Rubber encapsulated disc.
• Suitable for both horizontal and vertical
installation.
• Working Pressure: PN10, PN16.
• Available range: DN 50-300.
• Epoxy coated from the inside and outside,
min 250 μm in accordance with
EN 14901:2014
• Product color: Blue RAL 5005.
DOWNLOAD SPECIFICATIONS (PDF)
Telescopic service spindle
Features
• Allows valve opening and closing
• Easy to install without special tools
• Protection against dirt
• Adjustable in any position within the
range, and self-holding
• The protective tube, cap and clutch
between the telescopic parts are
integrated in a stable assembly
• With ranges from 0,7 to 2,5 m
DOWNLOAD SPECIFICATIONS (PDF)
Tensile Restrained Coupling for HDPE and PVC pipe
Features:
• Body and end ring are made of ductile iron material EN-GJS-500 (GGG
• 50) in accordance with EN 1563:2018
• Couplings for PE and PVC produced in accordance with EN 14525:2004
• Protection by epoxy coating or thermoplastic coating in accordance with
EN 14901:2014 or black color confirmed by health inspection certificate
• PN16 working pressure.
• Equipped with steel zinc plated bolts, nuts and washers
• EPDM rubber seals in accordance with EN 681-1:1996
• High Tolerance mechanical pipe fittings
• Angular deflection +/- 4⁰
DOWNLOAD SPECIFICATIONS (PDF)
Two part tapping saddle for PE-PVC pipes for tapping at full operating pressure
Features
• For installation on PE and PVC pipes
• For horizontal or vertical installation
• Operating pressure PN16 bar, hydraulically tested in accordance with EN12266-1: 2012
• Body made of ductile iron EN-GJS-500-7 in accordance with EN 1563:2018
• Epoxy paint surface protection of min 250μm in accordance with EN 14901:2014 or
thermoplastic confirmed by an accredited laboratory issued health inspection certificate
EPDM rubber seals in accordance with EN 681-1:1996/A3:2005 confirmed with an
accredited laboratory issued health inspection certificate
• Connector with internal female thread G1”, G1½” and G2” in accordance with EN 10226-
1:2004
• Additional material coupled with connection to PE hose min. Ø32 made of brass. The thread
of the additional material is in accordance with the ICC EN 10226-1:2004 and is designed
for a working pressure of 16 bar
• Telescopic extension spindle with ranges from 0,7 m to 2,5 m made of PVC and galvanized
steel with epoxy protected or galvanized coupling elements
DOWNLOAD SPECIFICATIONS (PDF)
Underground Hydrant DN80
Features:
• Design in accordance with EN 1074-6:2008:,
• Body, claw, cap and cone made of ductile ironENGJS-400-15 (GGG40) or EN-GJS-500-7 (GGG50)in
accordance with EN 1563:2011.
• Flange dimensions in accordance with EN 1092-
2:1997
• Hydraulically tested in accordance with EN 12266-
1:2012 with an accredited laboratory issued report.
• Automatic outlet for faster water draining
• Stainless steel spindle fixed with brass nut and
o-rings
• All elastomeric seals for underground hydrants
that come in contact with water are made of EPDM
material (antibacterial rubber) in accordance
with EN 681-1:1996/A3:2005 with an accredited
laboratory issued hygiene certificate.
• Surface corrosion protection with externally and
internally applied epoxy coating with minimal
thickness of 250μm in accordance with
EN 14901:2014
Underground Hydrant DN80 Type “ATA-T2”
Features:
• Design in accordance with EN 1074- 6:2008:,
• Body, claw, cap and cone made of ductile iron
EN-GJS-400-15 (GGG40) or EN-GJS-500-7
(GGG50) in accordance with EN 1563:2011.
• Flange dimensions in accordance with EN
1092-2:1997
• Hydraulically tested in accordance with EN
12266-1:2012 with an accredited laboratory
issued report.
• With ball safety system for automatic closing
and single or double automatic outlet for
faster water draining
• Stainless steel spindle fixed with brass nut
and o-rings
• All elastomeric seals for underground
hydrants that come in contact with water are
made of EPDM material (antibacterial rubber)
in accordance with EN 681-1:1996/A3:2005
with an accredited laboratory issued hygiene
certificate.
• Surface corrosion protection with externally
and internally applied epoxy coating with
minimal thickness of 250μm in accordance
with EN 14901:2014DOWNLOAD SPECIFICATIONS (PDF)
Universal tapping bridge for tapping at full operating pressure
Features
• For installation on cast-iron, ductile, steel and asbestos cement pipes
• For horizontal or vertical installation
• Operating pressure PN16 bar, hydraulically tested in accordance with EN12266-1: 2012
• Body made of ductile iron EN-GJS-500-7 in accordance with EN 1563:2018
• Epoxy paint surface protection of min 250μm in accordance with EN 14901:2014 or
thermoplastic confirmed with an accredited laboratory issued health inspection certificate
• EPDM rubber seals in accordance with EN 681-1:1996/A3:2005 confirmed with an accredited
laboratory issued health inspection certificate
• Connector with internal female thread G1”, G1½” and G2” in accordance with EN 10226-
1:2004
• Additional material coupled with connection to PE hose min. Ø32 made of brass. The thread
of the additional material is in accordance with the ICC EN 10226-1:2004 and is designed for
working pressure of 16 bar
• Telescopic extension spindle with ranges from 0,7 m to 2,5 m made of PVC and galvanized
steel with epoxy protected coupling elements
• Belt, rods, washers and nuts made of X5CrNi18-10
DOWNLOAD SPECIFICATIONS (PDF)
Wall sleeve flange Split puddle flange
Features
• Made from constructive steel min. St235JR
• For welding or installation on pipes that pass through
concrete walls
• Strengthens and fixes the pipe
• Per request, wall flanges can be made up to DN1600
DOWNLOAD SPECIFICATIONS (PDF)
XR – Tapers flange
Features:
• The pressure reducing flange allows for substantial reduction of the nominal
diameter and is very practical because of its overall short length
• Dimensions in accordance with EN 1092-1:2007+A1:2013/AC:2014
• Material: steel S235JR
• Zinc plated bolts in accordance to DIN975
• Working pressure: PN10 and PN16.
• Epoxy paint surface protection of min 250μm or thermoplastic confirmed by an
accredited laboratory issued health inspection certificate
DOWNLOAD SPECIFICATIONS (PDF)
Y strainer
Features
• Y- Pattern.
• Stainless Steel Screen.
• Working Pressure: PN10, PN16.
• Available range: DN 50-300.
• Epoxy coated from the inside and outside,
min 250 μm in accordance with
EN 14901:2014
• Product color: Blue RAL 5005
DOWNLOAD SPECIFICATIONS (PDF)