Repair clamp Type DI
Product characteristics
Repair clamps are flexible clamps composed of one, two or three stainless steel parts with ductile iron clamps attached to their ends with bolts and nuts for tightening. They are intended for easy, fast and permanent repair of corroded or damaged water pipes. The central bolt is with extended length for easier installation in difficult conditions. Working pressure PN10/16.Material
- Body and side plates made of stainless steel 1.4301 (AISI 304)
- Clamps of ductile iron in accordance with EN 1563:2018
- Surface protection of clamps with epoxy paint or black thermoplastic confirmed by an accredited laboratory issued health safety report
- EPDM rubber seal in accordance with the EN 681 -1:1996/A1:1998 with an accredited laboratory issued health safety certificate
- Screws, nuts and washers – Stainless steel (Class A21A4)
Field of application
- Above the ground installation.
- Underground installation.
Repair clamp Type S
Product characteristics
Repair clamps are flexible clamps made of one or two stainless steel parts wrapped with rubber gasket. They are intended for easy, fast and permanent repair of corroded or damaged water pipes.
The single band repair clamps are with tolerance of 10mm,
whereas the double band repair clams have 20mm tolerance.
Material
• Body and bands – stainless steel
• Rubber gasket – EPDM or NBR
• Nuts, bolts and washers – stainless steel
Field of application
• Above ground installation.
• Underground installation
DOWNLOAD SPECIFICATIONS (PDF)
Resilient Seated Gate Valve – F5
Features:
• Replaceable O-rings
• Low torque operation
• Rubber encapsulated wedge (optional
wedge with integrated sliders).
• Clockwise closing direction
• Epoxy coating protection in
accordance with EN 14901:2014
confirmed by health inspection
certificate
• Product color: Blue RAL 5005
• Maximum temperature: 80°C
DOWNLOAD SPECIFICATIONS (PDF)
Resilient seated gate valve F4
Features
- Replaceable O-rings
- Rubber encapsulated wedge (optional wedge with integrated sliders)
- Clockwise closing direction
- Epoxy coating protection in accordance with EN 14901:2014 confirmed by health inspection certificate
- Product color: Blue RAL 5005
- Maximum temperature: 80°C
Rubber Expansion Joint
• Flexible main shell made of EPDM in accordance
with EN 681-1:1996/A3:2005 with inner
reinforcements to provide consistency
• Steel galvanized loose flanges in accordance with
EN 1092-1:2007+A1:2013/AC:2014
• Working Pressure: PN10, PN16.
• Working Pressure: PN10, PN16.
• Available range: DN 50-600.
• Easy to install due to their light weight and
relatively small space requirement.
• Noise and vibrations caused by equipment such as
pumps are absorbed by Rubber Joints.
• Rubber Joints balance thermal movements appear
in any rigid system due to temperature changes.
Single chamber air valve
Features
• Design: EN 1074-4:2000
• Available range of DN sizes DN 50 to DN 100.
• Epoxy coated from the inside and outside, min 250
μm in accordance with EN 14901:2014
• Product color: Blue RAL 5005.
• Working pressure PN10 and PN16
DOWNLOAD SPECIFICATIONS (PDF)
Sluice gates Penstocks
Features
• Purpose: Wastewater treatment and mini hydro power plants.
• Made in accordance with EN 1085:2007
• Three or four side sealing
• Manual board lifting (option with hydraulic drive)
• Material:
Frame: Stainless steel in accordance with EN1.4301/X5CrNi 18-10 AISI 304
• Table: Hot rolled structural steel in accordance with EN 10025-2:2004 (option
stainless steel in accordance with EN1.4301/X5CrNi 18-10 AISI 304)
Stem: Stainless steel in accordance with EN 1.4301/X5CrNi 18-10 AISI 304 or
hydraulic cylinder with clip material C45E (1.991) in accordance with EN10277-
5:2008
Sealing tape: Hot roller structural in accordance with EN 10025-2:2004 or
stainless steel in accordance with EN 1.4301/X5CrNi 18-10 AISI 304
• Seal: EPDM rubber in accordance with EN 681-1:1996/AC:2002
• Surface protection by materials made of hot rolled structural steel with epoxy or
polyurethane color
DOWNLOAD SPECIFICATIONS (PDF)
